- #Rj45 k dcan cable pinout how to
- #Rj45 k dcan cable pinout serial
- #Rj45 k dcan cable pinout download
This is similar to a CAT5 cable except that CAT5 connects pin 1 to 1, 2 to 2, etc. Using the ADB0039 dongles for our Cisco routers worked just fine but the ADB0036 dongles didn't work for our foundry routers and the reason for this is those dongles expect a Yost "flat" RJ45 cable which connects pin 1 to 8, 2 to 7, etc.
#Rj45 k dcan cable pinout serial
Tonight I was working on installing an avocent cyclades CS4016 to connect to the serial consoles on all of our routers. This is because Foundry is one of the few companies that use a straight through cable rather than the crossed cable that almost everything else uses. (click on the Operation System to get the how-to guide directly).If anyone has ever worked with a router or switch from Foundry Networks, then you know how difficult it is to get into the RS232 console port using the standard cables that you usually have available.
#Rj45 k dcan cable pinout how to
How to install INPA software on Windows XP, Windows Vista 32bit, Windows 7 32, Windwos 7 64bit, Windows 8, Windows 10 users.
#Rj45 k dcan cable pinout download
W here to download & How to install BMW INPA software for K+Dcan cable : When you do this the DCAN functionality will no longer work though. How do you switch the modes physically? Do you use such a adapter to connect Pin 7&8?Ī : If you don‘t plan to use the cable on any cars that have DCAN(2007+) then you can pop open the case and solder a jumper between them. Q : I have a 2003 E39 so there is no OBD1 anymore. Worst cast scenario you just need to modify the cable & stuck a switch on it to toggle pin 8 on/off as needed.įinally there are a lot of rubbish adapter cables out there. The ones with pin 8 active are just older versions of the cable. The one with it disabled is ideal for e90 newer than 03/07 & that era, these leads often come with a black adapter to re-enable the pin 8 (by just tying it to pin 9) so it will also be suitable for e46/e39/e63 etc. With these K DCAN cables there are two subtle different versions, one with pin 8 enabled, one with it disabled. In fact thinking about it I use the same adapter for INPA, DIS and ISID. As mentioned if you only use the adapter on the e39, run the utility once and set the adapter to K CAN and leave it at that.
![rj45 k dcan cable pinout rj45 k dcan cable pinout](https://kds-online.de/images/OBD/33125_ENET-Adapter_A/33125_ENET-Adapter_A_01_1040x0780.jpg)
I use the DOS version of the DCAN utility. I always switch my K+D CAN adapter between K and D CAN protocols as I need to, depending on the car that I’m connecting to.
![rj45 k dcan cable pinout rj45 k dcan cable pinout](https://static.wixstatic.com/media/7de93e_7a35549923ce4bc5b4213be8562e8b69~mv2.jpg)
The OBD port only allowed access to limited modules, I think only the DME in fact. Q : How do I switch back to K-Line? Just by connecting the two pins or is further action on the computer required?Ī : Earlier e39 had both the OBD port in the cabin and the round 20 pin connector under the hood. If you run it the first time you connect to a DCAN car, your computer will retain the settings. Q : Is it necessary to do so every time I want to use DCAN or is the interface staying in DCAN mode once I ran DCAN.exe?Ī : You only need to run it when you are switching between modes. I have only used my K+DCAN interface with DCAN cars.
![rj45 k dcan cable pinout rj45 k dcan cable pinout](https://obd2diagtool.files.wordpress.com/2016/12/k252bdcan-inpa-cable-switch-pcb2b252812529.jpg)
Q : Is there anything else to do for switching from K-Line to DCAN then disconnecting pin 7&8? Unfortunately I don’t have a DCAN model available.Ī : As soon as you connect the interface to the car and your computer, run DCAN.exe to configure the comms rate. Q : So you have to physically connect (K-Line) or disconnect (DCAN) pin 7&8?Ī : Yes, I think connection by soldering is a bad option as it limits the usefulness of the interface, I have an adapter but consider a switch to be a better option. How to use/switch/connect to K-Line or Dcan pin 7&8?